Where is the vibration motor on iphone 4s

Related sponsored items. Showing Slide 1 of 2. Seller Free shipping Free shipping Free shipping. Similar sponsored items. Last one Last one Last one. Seller assumes all responsibility for this listing. For the rest of the repair, you can also use the metal laboratory spatula instead of the spudger.

This may make some steps easier for you. However, we explicitly recommend using the ESD spudger produced specifically for precision electronics. The antenna cover is under the battery connector. Remove the cover and put it in the same compartment of your organizer tray as the Phillips screws you removed before see figure 1. Now remove the battery. Insert the flat end of the spudger into the space about 1 cm to the left of the volume down button between the battery and the outer frame, and slowly lift the battery see figure 2.

Now you can also disconnect the antenna connector by carefully pulling it off the plug head using the spudger see figure 3. Fold the plastic tab with the warning over and press it firmly onto the lower adhesive strip. Of course, you can also remove the plastic tab. Remove the two Phillips screws from the dock connection cable and remove the silver cover see figure 1.

Now you can carefully detach the connector by using the pointed tip of the spudger to lift the connector. Alternatively, you can also use your fingernail again see figure 2. Remove the four Phillips screws from the cover see figure 1. In order to remove the cover, use the spudger to push it slightly to the left, toward the dock connector see figure 3.

Use the spudger to lift off the camera connector and remove the camera see figure 1. Use a pair of tweezers or the laboratory spatula to remove the black sticker below the flash see figure 2. Remove it see figure 3. Put all the parts in the same compartment of your organizer tray. Now you can disconnect the following five connectors. Be very careful.

Place the pointed tip of the spudger very slightly below the contact and lift it up. Start with the connector. Remove the Phillips screw on the antenna cover see figure 1. Put the screw in a separate compartment of your organizer tray. Put it with the screw you removed before. Disconnect the antenna connector below it using the spudger see figure 3. Now unscrew all four screws that hold the logic board in place see figure 1 and sort them as follows. It comes off easily.

With the right tools, you will succeed in any repair. In our store you will find a large selection of professional quality tools. Now remove the vibration motor. Be careful not to pry at the battery connector socket itself, or it may detach from the logic board.

There are four very small solder points awaiting this mistake! During reassembly, be sure to carefully position the pressure contact back in place. It should rest on top of the Philips screw post shown, and the gold contact should point towards the battery connector.

Be sure to clean the pressure contact with a degreaser such as windex or isopropyl alcohol. The oils on your fingers have the potential to create wireless interference. Insert the edge of a plastic opening tool between the battery and the outer case near the bottom of the iPhone. Run the plastic opening tool along the right edge of the battery and pry up at several points to completely separate it from the adhesive securing it to the outer case.

Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool. If there's any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.

Use the exposed clear plastic pull tab to peel the battery off the adhesive securing it to the iPhone. Be careful not to pull the plastic pull tab too hard as it can be ripped off very easily.

If your replacement battery came in a plastic sleeve, remove it before installation by pulling it away from the ribbon cable. If your replacement battery came with an uncreased cable, carefully crease the cable into the proper shape before installing the battery into the phone. While installing the replacement battery, temporarily connect the battery connector to the phone to ensure proper alignment.

Once the battery is glued in place, disconnect the battery connector. Perform a hard reset after reassembly. This can prevent several issues and simplify troubleshooting. Remove the following screws securing the dock connector cable cover to the logic board:. Use the edge of a plastic opening tool to pry the dock cable up from its socket on the logic board. Peel the dock connector cable off the adhesive securing it to the logic board and the side of the speaker enclosure.

Use the edge of a plastic opening tool to pry the cellular antenna cable up from its socket on the logic board. De-route the cellular antenna cable out from under the metal fingers attached to the logic board.

After Market Basic It is with widely accept major complaint replacements for original parts, which keeps a right balance between price and quality. Payment options. Possibly you may be interested. Similar products Already viewed products. Replacement For iPhone 4S Battery. Our company makes delivery all over the country.

We offer only those goods, in which quality we are sure. You have 30 days to test your purchase. Ordering Guide. Company Info. About us. Mon-Fri 9 am-6 pm.